-----------------------------------------------------------------------------
		Mauna Loa Solar Observatory Observer's Log 
-----------------------------------------------------------------------------
	Fri Aug 27 16:33:58 GMT 1999
Year: 99  Doy: 239
Observer: yasukawa
WEATHER COMMENT: Fri Aug 27 16:34:46 GMT 1999
Cool, clear, light southeast wind.
Fri Aug 27 16:35:18 GMT 1999	CHIP	 Startup--Initializing new tape
Fri Aug 27 16:39:34 GMT 1999	PICS	 Start Patrol
Fri Aug 27 16:39:58 GMT 1999	CHIP	 CHIP Start Patrol
Fri Aug 27 16:44:07 GMT 1999    MKIV    Start Patrol
**MKIV PROBLEM**: Fri Aug 27 16:48:33 GMT 1999
Bright regions on east and west, due to pre-sunrise condition (looking at
the dome wall) is streaky, dark regions not streaked.  Not sure if this is an
effect of all the changes going on with MKIV but it shouldn't hurt to 
reset the KCC while MKIV is still domed out.
Fri Aug 27 16:56:37 GMT 1999    MKIV    Start Patrol
**MKIV PROBLEM**: Fri Aug 27 16:59:32 GMT 1999
Streaks gone.
Fri Aug 27 17:01:49 GMT 1999	CHIP	 Bias
Fri Aug 27 17:02:38 GMT 1999	CHIP	 End Bias
Fri Aug 27 17:02:46 GMT 1999	CHIP	 Water
Fri Aug 27 17:03:22 GMT 1999	CHIP	 End Water
**MKIV PROBLEM**: Fri Aug 27 17:08:22 GMT 1999
Did a Cancel KccRead, then a KccRead & to pick up a new MKIV display 
for nahenahe.  Noticed that barrel stopped after first scan,this occurred before the Cancels.
David is currently trying to get things to work.
**MKIV PROBLEM**: Fri Aug 27 17:18:09 GMT 1999
Barrel stalled again.
Downloading new version of code again.
Fri Aug 27 17:26:12 GMT 1999    MKIV    Start Patrol
**MKIV PROBLEM**: Fri Aug 27 17:53:42 GMT 1999
David removed routine using raw data from the code and the program now
works.  Barrel is scanning and the MKIV gif images are being displayed
on nahenahe--very nice!
Fri Aug 27 18:00:48 GMT 1999	CHIP	 Bias
Fri Aug 27 18:01:45 GMT 1999	CHIP	 End Bias
Fri Aug 27 18:02:05 GMT 1999	PICS	 Flat
Fri Aug 27 18:02:05 GMT 1999	PICS	 Flat
Fri Aug 27 18:02:46 GMT 1999	CHIP	 End Water
Fri Aug 27 18:04:41 GMT 1999	PICS	 End Flat
MKIV COMMENT: Fri Aug 27 18:29:49 GMT 1999
Calibration pau.  Installing prime focus height mask to document new 
alignment.
MKIV COMMENT: Fri Aug 27 18:35:48 GMT 1999
Height mask in place, taking a couple of coronal scans.
Fri Aug 27 18:36:21 GMT 1999    MKIV    Start Patrol
Fri Aug 27 18:43:17 GMT 1999    MKIV    End Patrol
Fri Aug 27 18:43:37 GMT 1999    MKIV    Start Patrol
MKIV COMMENT: Fri Aug 27 18:44:05 GMT 1999
Running height mask test with opal in.
MKIV COMMENT: Fri Aug 27 18:50:09 GMT 1999
height mask test pau.  Removing mask.
Fri Aug 27 18:55:10 GMT 1999    MKIV    Start Patrol
MKIV COMMENT: Fri Aug 27 18:55:17 GMT 1999
Resuming patrol until time to reconfigure dome shutter.
Fri Aug 27 19:02:54 GMT 1999	CHIP	 Bias
Fri Aug 27 19:03:04 GMT 1999	PICS	 polarization_calibration
Fri Aug 27 19:03:56 GMT 1999	CHIP	 End Bias
Fri Aug 27 19:04:06 GMT 1999	CHIP	 Water
Fri Aug 27 19:04:42 GMT 1999	CHIP	 End Water
COMMENT: Fri Aug 27 19:05:57 GMT 1999
Stopping to reconfigure dome shutter.
Fri Aug 27 19:07:39 GMT 1999	CHIP	 CHIP End Patrol
Fri Aug 27 19:09:00 GMT 1999    MKIV    End Patrol
Fri Aug 27 19:13:48 GMT 1999	PICS	 End Patrol
Fri Aug 27 19:28:40 GMT 1999    MKIV    Start Patrol
COMMENT: Fri Aug 27 19:28:45 GMT 1999
Starting MKIII/IV and CHIP.  
HIP	 CHIP Start Patrol
PICS  COMMENT: Fri Aug 27 19:29:11 GMT 1999
Setting up PICS for Hartman mask focus test.
PICS  COMMENT: Fri Aug 27 19:30:58 GMT 1999
Will begin by testing software routine and taking a set of focus data
with micrometer setting at "original" setting of 15373.5
Hartman mask 3 cm. wide placed across middle of O1 in east/west direction.
Fri Aug 27 19:34:10 GMT 1999	PICS	 Start Focus
Fri Aug 27 19:40:31 GMT 1999	PICS	 End Focus
Fri Aug 27 19:42:23 GMT 1999	PICS	 Start Focus
Fri Aug 27 19:45:23 GMT 1999	PICS	 End Focus
PICS  COMMENT: Fri Aug 27 19:47:12 GMT 1999
Focus program needed modification to get the prompts to work but it
would not pause for data entry and prompts.  We decided to do the data
entry via phone and use abort to stop the program as end did not work.
Pausing test to determine which way camera moves per micrometer entry
and to set camera forward of current focus.
PICS  COMMENT: Fri Aug 27 20:02:53 GMT 1999
Founf directional info on sheet of paper that was hiding under the 
notepad.  A jog of micrometer UP, moves the camera to the rear.
Moved the camera forward 1000 microns and will begin test at 
14365.9 and move in +200 micron increments (approximately).
Fri Aug 27 20:07:22 GMT 1999	CHIP	 End Gain
Fri Aug 27 20:07:36 GMT 1999	CHIP	 Bias
Fri Aug 27 20:07:51 GMT 1999	PICS	 Start Focus
Fri Aug 27 20:08:29 GMT 1999	CHIP	 End Bias
Fri Aug 27 20:08:43 GMT 1999	CHIP	 Water
Fri Aug 27 20:09:18 GMT 1999	CHIP	 End Water
PICS  COMMENT: Fri Aug 27 20:12:29 GMT 1999
David modified the program, meanwhile, so that I could run the test
from the cmdtool window.  Tested it and it works so test is proceeding.
PICS  COMMENT: Fri Aug 27 20:23:30 GMT 1999
Ran from 14365 back to 15373.  Running +1000 microns beyond old setting now.
PICS  COMMENT: Fri Aug 27 20:37:19 GMT 1999
OK, ran thru micrometer settings.  Focus on disk looked good between 15373 and
15573(approximate).  I will try 3 more settings, approximately
15273, 15473, and 15673.... uh, maybe one more at 15873.
PICS  COMMENT: Fri Aug 27 20:41:14 GMT 1999
pushed camera forward to new micrometer setting 15264 and will work back
again.
PICS  COMMENT: Fri Aug 27 20:51:26 GMT 1999
OK, test is pau.  Setting focus back close to where it was, securing
camera, replacing covers, and removing Hartman mask.
Fri Aug 27 21:01:16 GMT 1999	CHIP	 Bias
Fri Aug 27 21:02:14 GMT 1999	CHIP	 End Bias
Fri Aug 27 21:02:31 GMT 1999	CHIP	 Water
Fri Aug 27 21:03:17 GMT 1999	CHIP	 End Water
COMMENT: Fri Aug 27 21:06:36 GMT 1999
Jostled spar around putting covers back on PICS.
MKIII/MKIV and CHIP hourly images probably hosed.
PICS  COMMENT: Fri Aug 27 21:07:41 GMT 1999
PICS back close to original focus.  Focus at 15371.3
Fri Aug 27 21:08:56 GMT 1999	PICS	 Start Patrol
PICS  COMMENT: Fri Aug 27 21:16:46 GMT 1999
Focus test images are stored on disk in Boulder with the micrometer 
settings attached to the files.  These will be analyzed there probably 
using an IDL program to determine the best focus.
MKIV COMMENT: Fri Aug 27 21:34:36 GMT 1999
Stopped, doing an End Day to initialize the barrel and then resetting
the KCC to pick up latest version of David's software for test.
Fri Aug 27 21:39:08 GMT 1999    MKIV    Start Patrol
MKIV COMMENT: Fri Aug 27 21:39:18 GMT 1999
Starting up Patrol with the new KCC software version.
**MKIV PROBLEM**: Fri Aug 27 21:42:41 GMT 1999
There were two radial dropouts on first pass.  Access Fault occurred 
after stop of first scan.  Message follows:

send_time
/local/d/Data/MkIII/21_39.rawmk3
 
Access Fault
Program Counter: 0x00073380
Status Register: 0x3004
Access Address : 0x04040443
Special Status : 0x0125
Task: 0x398ae4 "Dalsa"
/local/d/Data/MkIV/21_39.rawmk4

**MKIV PROBLEM**: Fri Aug 27 21:44:11 GMT 1999
Barrel not starting up again.  
**MKIV PROBLEM**: Fri Aug 27 21:47:04 GMT 1999
Downloaded the current version again, resetting KCC to pick it back up.
Fri Aug 27 21:50:53 GMT 1999    MKIV    Start Patrol
MKIV COMMENT: Fri Aug 27 21:51:01 GMT 1999
barrel initialized, starting Patrol.
**MKIV PROBLEM**: Fri Aug 27 21:51:59 GMT 1999
Image is not being written to display. Queueing up Idle.

**MKIV PROBLEM**: Fri Aug 27 21:57:04 GMT 1999
No gif image on nahenahe either, just a dark screen.  Scan did turn around 
OK.  Stopped at end correctly.
No image with last scan either.
Fri Aug 27 22:00:48 GMT 1999	CHIP	 Bias
Fri Aug 27 22:01:40 GMT 1999	CHIP	 End Bias
Fri Aug 27 22:01:50 GMT 1999	CHIP	 Water
Fri Aug 27 22:02:28 GMT 1999	CHIP	 End Water
**MKIV PROBLEM**: Fri Aug 27 22:04:00 GMT 1999
David had no clue as to what went wrong, we supposedly had the program
that was working loaded.  Resetting KCC and trying again.
**MKIV PROBLEM**: Fri Aug 27 22:05:55 GMT 1999
Could a "4p" I typed in while cursor was in akamai window by mistake,
did not do a return because Messages were flying by at the time,
cause program to screw up???
Fri Aug 27 22:07:38 GMT 1999    MKIV    Start Patrol
**MKIV PROBLEM**: Fri Aug 27 22:08:28 GMT 1999
KCC display is back.  I almost did it again... mouse had moved cursor into
akamai window unbeknownst to me, and I started typing a log entry.
fortunately David has the system *IN USE* via rlogin.  Nothing got
written to akamai window by that screw-up.
Fri Aug 27 22:11:26 GMT 1999	PICS	 End Patrol
Fri Aug 27 22:11:26 GMT 1999	PICS	 End Patrol
Fri Aug 27 22:12:43 GMT 1999	CHIP	 ending tape
COMMENT: Fri Aug 27 22:16:01 GMT 1999
Tapes
MKIV:  99-239
PICS:  P01531  
CHIP:  C00907
LOWL:  L00622 in drive 0
Fri Aug 27 22:21:24 GMT 1999 
	MkIII	
 
16_44.rawmk3   18_04.rawmk3   19_39.rawmk3   20_31.rawmk3   21_23.rawmk3
16_47.rawmk3   18_11.rawmk3   19_42.rawmk3   20_34.rawmk3   21_26.rawmk3
16_56.rawmk3   18_18.rawmk3   19_46.rawmk3   20_38.rawmk3   21_30.rawmk3
17_12.rawmk3   18_25.rawmk3   19_49.rawmk3   20_41.rawmk3   21_39.rawmk3
17_26.rawmk3   18_36.rawmk3   19_53.rawmk3   20_45.rawmk3   21_51.rawmk3
17_29.rawmk3   18_39.rawmk3   19_56.rawmk3   20_48.rawmk3   21_54.rawmk3
17_33.rawmk3   18_43.rawmk3   20_00.rawmk3   20_51.rawmk3   22_07.rawmk3
17_36.rawmk3   18_47.rawmk3   20_03.rawmk3   20_55.rawmk3   22_11.rawmk3
17_40.rawmk3   18_55.rawmk3   20_06.rawmk3   20_58.rawmk3   c18_07.rawmk3
17_43.rawmk3   18_58.rawmk3   20_10.rawmk3   21_02.rawmk3   c18_14.rawmk3
17_46.rawmk3   19_02.rawmk3   20_13.rawmk3   21_05.rawmk3   c18_21.rawmk3
17_50.rawmk3   19_05.rawmk3   20_17.rawmk3   21_09.rawmk3
17_53.rawmk3   19_28.rawmk3   20_20.rawmk3   21_12.rawmk3
17_57.rawmk3   19_32.rawmk3   20_24.rawmk3   21_16.rawmk3
18_00.rawmk3   19_35.rawmk3   20_27.rawmk3   21_19.rawmk3